Hello everyone! Could you tell me how and where to change the ITU region?
The condition from BandMenu.svelte does not work for region 1

Just seeing this now!  I like this idea.  Going to give it a try!
Can this log inbound request with their originating IP?

Is anybody aware of any type of substantial logging for novasdr site access and relation between users in the chat and their IP address?  I setup logging in my gateway router, but I have no way to identify a user's chat messages to their IP addresses.  I'd also like to identify who is sending in the obviously malicious LONG url's and crashing the server constantly.  It seems chat messages disappear after a period of time from the small chat file, and I can't find any log files.
I was considering setting up a wrapper site in apache but that really messes with things, and the users can still figure out the novasdr direct access if they view the page source. :-(

Quote from: hb9ryz on 30 Nov 2025, 21:24 It worked, but my HP ProDesk 400 G2 Mini PC with only 8GB memory is not strong enough to run PhantomSDR-Plus even without or with accelerator.

A temporal solution might be to play with sps in .toml . Default is 60000000 (for 30 MHz range). Try to make it e.g. 20000000 for 10 MHz range and check the behavior of the stream.
You even can play with fft_size. The default for RX888 is 8388608, but you can pick up some other values such as 1048576, 2097152, 4194304. This will help you maybe to start server without artifacts, until memory stick to arrive, or until to find another solution with the pc.
Please try to type top in terminal and give the results.
Type also sudo intel_gpu_top and check the results if Render/3D is too high.

Hi All
Emmanuel SV1BTL helüed me remotely via AnyDesk to install his version of the PhantomSDR-Plus.

Thank you very much Emmanuel.

It worked, but my HP ProDesk 400 G2 Mini PC with only 8GB memory is not strong engough to run PhantomSDR-Plus even without or with accelerator.

So I just ordered additional memory for this PC.

73 de HB9RYZ
Wolfgang

You do understand that painting the DX-cluster in the waterfall is a massive task when there are many users.
As the waterfall is rendered, every Dx-cluster entry has to be rendered too.
Also, how long do they show? I do not believe this is a god idea. Flex is just doing it for 1 user, namely you.
Also how many bands? All bands? What about 27Mhz clusters? It needs to connect to ALL clusters to do it.

The latency is good enough for FT4/8, just make sure your samplerate is 12KHz AND your systemclock is synchronised so it can decode. But it should be changed to decode and report by itself. If possible. Latency is not an issue, sorry.

You can mark all CB-channels yourself, not hard to do. As it also differes what modulation is used, there isn't a real standard in the world.

As for band buttons, same issue, there are too many bands, so the box will alter all the time, not everybody uses it for HF only, some VHF or UHF. Band-buttons in a box will always be a problem for everyone.

But hey, it's open-source, you make all changes yourself

As for mouse-freq-wheel, I believe that is on Steven's list already.

Hi All
This is my wishlist for the new PhantomSDR Plus:

- freq. tuning in the freq-Digtal-Number-Window with the mouse wheel
- DX-Cluster shown in waterfall as done in Flexradio SmartSDR
- good latency in order to use FT4/FT8
- all CB channels with marks
- Band-Button near of the main-window, just under the freq.-window

73 de HB9RYZ
Wolfgang

Try this:

https://www.phantomsdr.fun/index.php?topic=166.msg931#msg931

Did you update NPM when it told you to update?
As you shouldn't do that.

See old forum to reverse it back.

A modified Auto Squelch is installed in my server and works. But my SDR is using the older version of PhantomSDR